autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only

RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Media Type: Auto-MDIX; Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only For J9537A, J9549A, J9535A, and J9637A modules: K.15.02.0004 (for J9054B/C 1990-3613); K.15.08.0007 (for J9054C 1990-4112 and 1990-4483) J9054D: K.15.08.0007 It prioritises traffic by specifying a port and priority level. VLAN-based prioritises traffic by specifying a VLAN and priority level. Supports Airwave Network Management software to provide common platform for Zero-Touch Provisioning management, and monitoring for wired and wireless network devices.

dual-personality ports; each port can be used as either an RJ-45 10/100/1000 port (IEEE 802.3 Type 10Base-T; IEEE 802.3u Type 100Base-Tx; IEEE 802.3ab 1000Base-T Gigabit Ethernet) or as a SFP slot (for use with SFP transceivers) It sets per-port ingress enforced maximums for all ingressed traffic or for broadcast, multicast, or unknown destination traffic. For use in the SFP ports on the models listed, and in an installed J9312A 10GbE 2-port SFP⁠+/2-port CX4 yl Model For J8692A, J8693A: K.12.01 (for J9054B/C 1990-3613); K.15.08.0007 (for J9054C 1990-4112 and 1990-4483, and J9054D 1990-4483 and 1990-4360)

RJ-45 10/100/1000ポート(IEEE 802.3 Type 10Base-T、IEEE 802.3u Type 100Base-Tx、IEEE 802.3ab1000Base-T Gigabit Ethernet)またはSFPスロット(SFPトランシーバーに使用)ポートとして使用可能ArubaOS-Switch Software Feature Support Matrix for XX.YY (where XX.YY is the software branch you're interested in) document would shed some light about which features are implemented on which XX.YY Software Branch. Only supported for use in SFP⁠+ ports on JL658A. 100-FX is not supported for use in any SFP56 ports on other models.

Now few words regarding the "recommended software version"...actually, as you can see, for your Aruba 2530 (that is fairly generic for the entire Aruba ArubaOS-Switch NOS) there are 5 (five!) current software branches all receiving updates: For J9263A, J9264A: K.14.03 (for J9054B/C 1990-3613); K.15.08.0007 (for J9054C 1990-4112 and 1990-4483) Yes, if you have the HP/HPE/Aruba SKU (in your case it is J9775A representing the Aruba 2530 48G Switch model) you can go to the HPE My Networking portal (see here) found here: IEEE 802.3 Type 10BASE-T、IEEE 802.3u Type 100BASE-TX、IEEE 802.3ab Type 1000BASE-T)、通信方式：10BASE-T/100BASE-TX：半二重または全二重、1000BASE-T：全二重のみ For use in the SFP ports of the 2530 Series Switches. (The J9853A, J9854A, J9855A, and J9856A models have 1G/10G SFP⁠+ ports that do not support these 100Mbps transceiver modules.)The YA.16.08 (generically the 16.08) is the cutting edge and it includes all the new features, the most conservative is now the the 16.02...personally I use the 16.05 and the 16.08...but it boils down to what feature you need (16.08 has more feature than 16.07, 16.07 has more than 16.06 and so on...). The 8325 requires configuration of "interface groups" (groups of 12 ports) to enable the use of 1G or 10G transceivers / DACs in the SFP28 ports (default is to use 25G transceivers / DACs).